Skip to main content

If your iPhone 13 Pro has a broken or cracked screen, you may need to replace the entire assembly. This guide will show you how to replace the Red LCD Screen Assembly using a replacement part from Apple.

Display assemblies, also called LCD screens or panels, are a common component in modern smartphones and other mobile devices. They provide the user interface and visual content for the device. They typically use liquid crystal displays (LCDs), which are small and thin pieces of glass that are coated with a layer of light-sensitive material that changes color when an electric current is applied. LCDs are used in phones, tablets, laptops, TVs and other electronic devices because they offer high resolution, brightness and contrast levels.

A display assembly includes the LCD panel itself as well as all of the associated hardware and circuitry needed to display images on the panel. The assembly usually resides inside a sealed housing that protects it from the environment and enables it to be mounted on a circuit board. In many cases, the assembly also includes one or more buttons or touch screens that allow users to interact with the device.

LCD screen assemblies can be broken if they are dropped or damaged in some other way. If this occurs, it can be difficult or impossible to repair or replace the screen assembly without damaging additional parts of the phone. This is why it is important to keep your phone’s display assembly properly protected by using a case or sleeve when you’re not using it.

A broken or damaged LCD screen can stop your IPHONE 13 PRO from functioning properly. Replacing the screen assembly is a simple, affordable solution that will restore your phone to its original condition.

The iPhone Pro uses a different assembly than other models, so be sure to order the correct part if you need to replace the screen.

There are several online resources where you can find step-by-step instructions for replacing your LCD screen on an iPhone Pro. Be sure to read through these instructions before beginning work, as there are some specific tools and techniques required for this repair.

The iPhone Pro comes with a beautiful red LCD screen. However, over time the red color may start to fade and become less vibrant. This is because the red light used to display on the screen is shorter than other colors, and it’s also more prone to fading. If you’re experiencing this issue, replacing your old LCD screen assembly with a new one may help restore the vibrancy of your Red iPhone Pro screen.

LCD screens are usually replaced when they start to show signs of wear and tear. While there are other factors that can also contribute to poor screen vibrancy, such as using a screen protector that reduces glare or reducing battery usage, replacing an old LCD screen assembly is usually the best solution for restoring its original appearance.

There are a few reasons why you may need a new red LCD screen assembly for your iPhone Pro. If the screen is cracked, damaged, or just doesn’t look very good anymore, it’s time to replace the entire assembly. Another reason to replace the LCD screen assembly is if there is something wrong with the backlight. This can make viewing photos and videos difficult or impossible.

If your iPhone screen is busted or just needs a new LCD assembly, replacing it is relatively easy. All you need are the correct tools and some knowledge of how to take apart a phone.

First, loosen the screws that hold the front panel on. Once they’re loose, gently pry the panel off of the phone.

Next, remove the ribbon cable that connects the LCD to the motherboard. You can do this by removing screws from either end of it or simply pulling it out.

Finally, replace the broken or old LCD with a new one by following these steps:
1) Disconnect all cables connected to the old LCD.
2) Strip 1/4″ (6 mm) of insulation from each end of two male-to-male jumpers (J1 and J2), then crimp them onto each end of a new LCD cable (LCD_CABLE).
3) Insert J1 into J2 on one side of an empty slots on the motherboard, then insert J2 into J1 on the other side of an empty slots on motherboard. Note: The black lead should be facing down when inserting J1 into J2.


4) Replace screws in their corresponding holes in front panel and tighten gently using a Phillips screwdriver for now.
5) Solder jumper wires onto both ends of LCD_CABLE and wrap them around pins along edge of motherboard before soldering them in place with a small

Related Problems and Solutions

One of the most common issues that iPhone users experience is a red LCD screen assembly. This can be caused by a number of different problems, but often it’s the result of moisture getting into the device and causing corrosion to the electronic components.

There are a few ways to fix this issue. If you’re able to open up your phone, you can try to remove the LCD screen and dry it out with a hair dryer or air compressor. If that doesn’t work, you may have to send your phone in for repairs or replacement.

If you’re not able to open up your phone or if fixing it yourself is too expensive or time-consuming, you may want to consider buying a new iPhone instead.

Introducing the brand-new Red LCD Screen Assembly for iPhone 13 Pro from Apple, featuring a sleek and stylish black finish. The new display assembly is designed to seamlessly integrate into your latest iPhone 13 Pro device, giving you the smooth and crisp visuals you’ve come to expect from the world’s top brand.



This advanced display assembly maintains the superior picture quality of your device and features full-color accuracy and all the features you have come to expect from your favorite phone. With a state-of-the-art backlight, there’s no blur and no ghosting, giving you the optimal viewing experience every time. The LCD screen is also resistant to impact and drop damage, ensuring long-lasting durability and top-notch performance, even in the most challenging environments.



The display assembly also has a wide viewing angle, allowing you to get the best out of the device regardless of how you hold the phone. This means you won’t miss a beat of your favorite shows, movies, and games. Additionally, the new display reduces the levels of eye strain and fatigue caused by prolonged use due to its innovative design to reduce harm to your eyes.



So don’t wait any longer – upgrade your iPhone 13 Pro with the new Red LCD Screen Assembly from Apple, featuring a sleek and stylish black finish. Buy yours today and enjoy the optimal viewing experience that this advanced display has to offer.

Leave a Reply

Close Menu

Wow look at this!

This is an optional, highly
customizable off canvas area.

About Salient

The Castle
Unit 345
2500 Castle Dr
Manhattan, NY

T: +216 (0)40 3629 4753
E: hello@themenectar.com